Pay attention to the details of home decoration to

  • Detail

1. Phenomenon of wall grooving

buried pipelines must be grooved on the wall and ground before they can be buried. A few workers carried out barbaric construction during slotting operation, which not only damaged the load-bearing structure of the building, but also may cause damage to other nearby pipelines

reminder: before construction, confirm the direction and location of the pipeline with the construction team leader again. For different wall structures, the requirements for slotting are also different: the load-bearing wall in the house is not allowed to be slotted, and the wall with insulation layer is easy to cause cracking on the surface after slotting, while the slotting on the ground should be careful not to damage the floor, causing trouble to the downstairs residents

2. Phenomenon of wires passing through pipes

in home decoration construction, almost all wires are passed through PVC pipes and buried in the wall. Therefore, after the wire is threaded into the PVC pipe, the consumer cannot see it at all, and it is difficult to replace it. If the workers are not careful in operation, the wires will be twisted in the pipe, causing hidden dangers of electricity. If workers deliberately cut corners, they will use wires with connectors or thread several wires in the same PVC pipe

reminder: consumers had better buy Wires by themselves, then supervise workers' operation on site, and conduct power on inspection after installation. In addition, consumers must let the decoration company leave a pipeline diagram. When the electrician just buries the wires into the wall, he can number these walls and draw a plan, then draw the direction and specific position of the wires with a pen, indicating the direction from the floor above, from the ground below and adjacent to the wall, especially the joint position of the pipeline, so that once there is a fault, the line position can be found immediately

3. Wire connector

phenomenon: electricians do not connect wires according to construction requirements when installing sockets, switches and lamps. Especially when consumers use some water heaters, air conditioners and other electrical appliances with large power consumption, switches and sockets are heated and even burned, which brings great losses to consumers

reminder: during construction, supervise electricians to carry out construction in strict accordance with the operating procedures. After the installation of all switches and sockets, be sure to carry out actual use to see whether these parts have heating

4. Sewer pipeline

phenomenon: the construction team sometimes pours debris containing a large amount of cement, sand and concrete into the sewer in order to save trouble during decoration. The direct consequence of this is to seriously block the sewer, causing the kitchen and bathroom to run away due to poor drainage. Although there is no problem in the final acceptance of some projects, there is always the problem of poor drainage

reminder: strictly supervise the construction team and do not use sewers as garbage lanes. After the waterway construction is completed, fill all water basins, basins and bathtubs with water, and then check whether the drainage is smooth and whether there is leakage in the pipeline

5. Facet treatment

phenomenon: the so-called facet is a small place that consumers can't see and don't pay much attention to, such as the upper edge of the door, the lower part of the windowsill, the inside of the heating hood and other places. Some workers cut corners here, and even don't do any treatment

reminder: remember that any object has six planes, and don't ignore any detail when checking the project quality

6. Base treatment

phenomenon: before painting emulsion paint and paving wall and floor tiles, the base treatment must be done well. Some workers cut corners in this aspect during construction, which may cause uneven walls, color difference after latex paint is applied, or discoloration and falling off of latex paint, or poor pasting of ceramic tiles

reminder: in the paving construction of wall and floor tiles, you should pay attention that tiles cannot be directly paved on the surface of lime mortar, lime paste, paper reinforced lime paste, machete lime paste and emulsion paint. They can be paved only after the base surface is cleaned

7. Phenomenon of wall painting

emulsion paint is the most common wall decoration material at present, which can be painted, roller painted or sprayed in specific construction. If workers are not serious or perfunctory during construction, small color differences often appear. This is especially true of latex paints with darker colors

reminder: before using the emulsion paint, you need to add a certain amount of water, and the prepared emulsion paint should be used up at one time. The paint of the same color should also be painted at one time. If the wall needs to be repaired after construction, the whole wall should be painted again

8. Joint decoration

phenomenon: the butt joint of some walls and doors and windows, as well as the butt joint of two different colors of paint, is where workers often perfunctory. You often see that the coatings between emulsion paint and wood are mixed with each other, and various problems occur at the joints

reminder: the treatment of joints is very important. You must supervise the workers to work carefully. If there are two colors of paint connected on the wall, the adhesive tape must be pasted on the edge of the first color during the construction, and then the paint of another color must be painted on it, so as long as the adhesive tape is torn off after the construction, the whole joint can be very neat

9. Wall and floor tile paving phenomenon: paving wall and floor tiles is a highly technical process. If the workers cut corners, they are most likely to have problems such as hollowing of tiles and uneven joints. In addition, the cement and adhesive used for paving tiles are also exquisite. If the proportion is unreasonable, there will also be problems such as falling off

reminder: according to the "quality acceptance standard for family room decoration engineering" issued by the Beijing Municipal Construction Commission, it is required that the wall and floor tiles should be paved smoothly and firmly, with clear patterns, no dirt and mortar marks, basically the same surface color, uniform joints, no cracks, corners and missing edges in the plate, and local hollowing should not exceed 5% of the total

10. Ground leveling

phenomenon: the ground of some houses is not flat enough and needs to be re leveled during decoration. If the workers are not careful or deliberately rough, it will cause the problem of getting more uneven. Moreover, the cement mortar used in the construction will greatly increase the ground load and bring hidden dangers to the safety of the building

reminder: before the ground leveling, the base treatment of the ground must be done first, and then the ground leveling must be carried out with cement mortar. After the cement dries out, use a special level to determine the flatness of the whole ground, and then proceed to the next step of construction




Copyright © 2011 JIN SHI